How to repair bifold door top roller (moved here) Guide

If your bifold doors are sticking then it's likely that they need some attention. You may need to clean and lubricate them or adjust them. The issue could be caused by a loose bolt at the top pivot or by the top guide roller.

This kit comes with all the hardware needed to bring your bi-fold closet door to optimal performance.

Take the door off

It might seem difficult and challenging to put in an internal set of bifold doors but for DIYers with a little experience, it's actually a breeze. Moving the frame isn't a problem The trick is getting the doors to fold and close quickly and accurately. Since bifold doors are complicated machines, they might require some tuning to keep functioning properly. It could be as easy as tightening the screw, or as intricate as taking off and replacing the pivot pin or roller.

The majority of the time, you can solve these issues with a couple of simple adjustments, without having to remove the doors. You might notice that your bifold doors are sliding or scraping the floor, or jumping out of track. It's not difficult to fix these problems. Just follow three simple steps and your bifold door should be back in the right direction in short time.

The most frequent issue that internal bifolding doors encounter is that they slide out of alignment. This can be caused by loose screws, holes in the anchor/pivot pins or simply a misaligned door. Most of the time, this can be corrected with a few simple adjustments. However, if your door isn't moving in any way, you might require replacing it.

You'll need to remove the door using a screwdriver, and possibly pliers to loosen any pivot pins that are too tight. The screwdriver can be used to release any locking levers that are on the bottom bracket for pivoting, and the pliers will allow you to pull the pin to release it and then take it off.

When the top roller has become loose and the top roller is loose, you should be able to lift the door and swivel it down and allow you to pull it out of its track and pivot brackets. It's usually a simple procedure, but you need to be cautious not to let the door hit the frame of the door. Then you can sand the edge of the door to make it smooth. You can then repaint or refinish it as required.

Remove the Roller Guide

This spring-loaded guide roller is mounted on the top of bifold door repair bracket doors to aid in smooth operation. It is specifically designed for Kenna frames, and can fit door panels from 1 inch to 1-3/8 inches thick. It is made from nylon, steel and plastic components. It can replace an old guide.

To begin to remove the roller guide, remove the screws that hold it in place. Do this using a screwdriver and a bit to loosen it. Use your hands to carefully remove it from the frame. It might require some effort to take off the door, so ask an assistant to help.

Once the guide you used to guide your child is removed, carefully cut through the remaining finish around the foot of the new guide with a sharp blade to remove it from the rod blank. This will make it easier to take off and ensure that there is no damage to the new guide foot. The guide foot is extremely sharp and could cut or snag fingers.

You will probably have to apply a little force to pull the guide off, but take care not to chip or break the foot. After you have removed the old guide, remove any remaining epoxy or threads in the place where it was fixed. This will prevent future problems with the guide.

After removing the previous guide, check the new one by placing it in its permanent position. Apply a few rotations using masking tape or guide tubing to ensure it stays in place. This allows you to check the guide alignment and spacing to ensure that everything is set up correctly. It doesn't matter if you're looking at it from a distance or using the dependable CRB Spine Finder and Deflection System, this step is important to avoid any problems in the future.

The last step is to replace the door. If the guide is in the correct position and functioning in the correct way, then you're ready to proceed. Remember to tighten and replace any screws or pins that you removed or loosened.

Take the Bottom Pivot off.

Bifold doors can be an attractive addition to any home, but they often need to be tweaked or adjusted to ensure they are in good shape. While some of the more straightforward issues can be resolved with the doors still in place, other issues will require removal. This guide will guide you through the process of removing internal bifold pivots for doors, pins and rollers so that you can make your doors slide like new.

Gathering your tools is the first step. Making sure you have everything in place prior to time will make it easier later in the process. You'll also need pliers and a screwdriver. You can buy an assortment of basic tools at your local hardware store for a reasonable cost. Keep some wood glue in the back of your hand. This can be useful if you have to glue any of the rollers back into place.

Once you've got the tools, begin by opening the bifold doors and then loosening the top track bracket using your screwdriver. Once the bracket is loose, you should be able slide the door off of the top track. It might take a small amount of jiggling, but it should pop right off the track.

Next, you'll need to remove the bottom pivot from the frame. Close all interior doors before beginning. This will be a lot easier than working from inside. If the bottom track still looks good it is possible to lift the door and Repair Bifold Door Top Roller remove the track.

You will need to replace the track if damaged. You can get tracks that are suitable for repairing bifold doors doors as well as swinging closet doors from a local hardware store. If the track is badly damaged then you may need to replace it entirely.

Now that your track is repaired or replaced You'll need to test the doors for their proper operation. Make sure that the doors move in and out of their position easily. You'll also want to check that the edges of the door are parallel to the frame when it is closed. If they're not, you'll need to adjust the top pivot bracket by tightening or loosening the bottom screwscrew.

Replace the Roller

Bifold doors are a great way to enclose closets or laundry rooms, as well as pantries, but only if they function properly. Bifold doors comprise two panels that are hinged and slide along tracks at the top of the frame. Over time the roller guides may wear out and cause the doors to sag. The guide roller can be replaced in just a few minutes using a few tools.

The first step is to remove the roller guide from the door panel. This involves removal of the bottom pivot bolt and loosening the screw that holds the guide to its top. After the guide is removed then lift the door frame up and away from its track. Then using a wrench remove the top pivot bolt from the hole in the header of the frame by loosening the nut.

A replacement top nylon roller guide with a 7/8 " diameter wheel and a base made of steel is available from Stanley, Cox or Acme. It is mounted on the top edge of bifold doors that are 1 to 1-3/8 inches thick. It is spring loaded and self-adjusts in the upper track to ensure smooth glide.

A bifold door roller replacement door can also scratch the floor as it opens and closes. This can occur after adding carpet or other flooring materials that require the doors to be raised slightly to allow for adequate clearance. The removal of the screw that adjusts the bottom pivot, loosening the top track's mounting screws and moving the anchor pin usually enough to clear this issue.

A new set of top roller guides is a low-cost solution to a problem that can make bifold doors difficult to operate. They're usually available at your local hardware store in the door section, but they're also available online from a number of vendors. In addition to a new top guide for rollers, you'll require a small bottle of Elmer's wood glue, which is sold in the big box stores and a squeeze clamp. The clamp is used to keep the repair area in place after the glue has been inserted and allowed to dry.