replacement upvc door handle UPVC Door Handles

Find the perfect handle for your door, whether replacing your handles or adding extra security. The Upvc handles are simple to install and meet the minimum 92mm centre distance of multipoint locks.

The most important measurements to consider are backplate fixing centres and lever/key hole dimensions. Compare these measurements carefully with your existing marks before ordering.

Lever/Pad

Lever pad door handles consist of the lever handle on one side and a paddle-shaped handle on the other. These are designed to be used with key wind locks, however, they can also be adapted to split spindle multipoint door locks (though you'll require an additional dual spindle lock case).

Our range of upvc handles lever pads are available in a wide range of finishes. They will be listed in the drop down list once you have found the correct handle for your door. Not all styles of handle are available in every finish and you should always look over the technical drawings and sizes sections for the specific product you're looking for to ensure that you get the correct size and fitting.

When selecting a new set of lever pad door handles made of upvc, it is essential to ensure that they match the PZ (distance between the handle spindle and the center of the cylinder hole) of your existing multipoint door locks, as they need to be in the same line to allow doors to remain locked, whether from the inside or the outside. Our handles are designed to fit a wide range of conventional cylinders, but it is a good idea to double-check before purchasing.

If you wish to upgrade to dual spindle levers you will need to remove the handles that are currently in use and then disassemble the lock case. This will require an extra split cylinder inline. These are available separately, and we provide a full technical diagram to take a look at in the pictures for each product.

It is recommended to loosen the screws that are holding your existing door handle and then inspect the mechanism. It is possible that you will need to loosen the screws further if they are not tight, and then you can remove the spindle and handle and replace it with a new door handle made of upvc. It is essential to ensure that the handle is in the proper position prior to installing it. You can do this by placing your finger between the frame and the handle to make sure that it's in the right position.

Lever/Lever

The lever door handles are used to operate a multi-point lock with the Euro cylinder. They can be found on a variety of double upvc doors, as well as on some wooden and aluminum doors. They feature a lever on the inside and an outside paddle and are usually supplied in two different types. Sprung - these include a spring cassette inside the backplate to move the handle lever to the horizontal position. Non-sprung: They do not have a mechanism to spring the handle lever to a horizontal angle.

To fix a sagging lever door handle you must find the hole for access to the detent or pin, which is typically a small round or replacement upvc Door handle rectangle with a protruding hole that is located on the opposite side of the base plate. Once you have located the detent access hole or pin, you can remove it with the help of a screwdriver.

Once the handle is in a horizontal position you can re-install the screws and tighten them so that the handle is secure on the base plate. Consider applying a threadlocking solution to the threads of screws to increase grip and prevent them from loosening over time.

There are many reasons that door handles for levers droop. The most common cause is that the fixings are over tightened and are putting stress on the bearings of the lever, causing it to bind against the door's surface. It could also be that the levers haven't been adjusted at the right angle, which compresses the latch mechanism and prevents it from fully springing into motion.

Another common cause is that the sprung lever isn't working properly. This is typically due to the spring not being in the right position within the backplate. The easiest way to test this is to turn the handle to check whether it returns to the horizontal position.

It is essential to repair upvc door handle any door handles that are loose immediately. This can cause excessive wear on the screws, and the handle may even be able to fall off the base plate. You should also tighten loose screws frequently to stop them from becoming looser.

Lever/Snib

The handles for doors made of upvc are also known as 'Snib' handle sets and have a snib button at the top of the lever that you can push down to lock your door handle repair if you don't have a Dummy lock. They usually come with a Fullex 68PZ (that's 68mm between the spindle's center and lever or lock centre) door lock. We also stock a range of 68PZ door handle from brands like Ferco and Fab & Fix.

Changing your door handle is a cost-effective way to update your home door handle repair near me, whether replacing existing handles or fitting new ones on doors that you've constructed in your home. There are many styles of door handle lock repair handles made of upvc with traditional levers on backplate, straight or curving short latch and knob handles with dummy handles for multi point locks, that are perfect for French doors.

Rose door handles are circular or oval-shaped versions of lever-on-backplate handles. These handles are identified by a lever or knob that is mounted on the backplate. The backplate is removable for hidden fixing.

These handles are available in a variety of finishes including coloured and chrome finishes to be matched to your door and hardware like knobs, bolts and hinges. Some handles come with grub screw to attach the knob or lever securely to the spindle. Other handles come with bathroom spindles that can be used to control bathroom locks and include a thumbturn turn and release mechanism, which is ideal to use on doors for bathrooms.

Mortise

The tubular latch is most likely to be the cause when your door handle made of uPVC is stuck open. This can be caused by various reasons however the most frequent is the lack of lubrication on the latch plate. This can be fixed quite easily by opening the door and replacement uPVC door handle spraying lubricant onto the lock and handle. It could also be that the latch has slipped away from the backplate. This can be a bit more problematic and requires a professional to fix.

A multipoint handle is the ideal solution to a stuck door handle. These handles are mounted on the faceplate of the door and are operated by the thumb turn knob or key which activates a cam that locks the deadbolt. The handles are available in a range of different sizes to fit various kinds of uPVC doors and come in a variety of attractive finishes to complement the existing hardware. The handles can be purchased on the internet or through an authorized locksmith in your area. They can be installed with clear instructions.

To select a replacement handle set, you'll have to know the PZ size of your cylinder. This is the distance from the edge of the door frame to the centre point of the hole for the handle in millimetres. You will also need to know if your door has hook-style locks or a mortise lock. The most efficient way to locate the correct handle once you know the measurements is to use the filter for brands on the website. This will help you narrow down your options and then you can choose the correct size.

A typical handle set comes with the handle unit with a pair of various length screws drilling guides, as well as installation instructions. The smart versions, such as the Igloohome Smart Mortise 2+, include a complete mortice lock with built-in keypad. These are more complex models that are best for professionals or highly skilled DIYers. Certain handle sets come with various accessories, such as weather strips, which can be used to enhance appearance of the door.